Taping And Chaining Assignment & Homework Help

Taping And Chaining Assignment Help

The measurement of space with the help of tape or chain is known as chaining. When measuring space together with the help of tape, the expression chaining ought to be used for the space measured with the aid of chain; the expression taping ought to be used. However, the expression ‘chaining’ is used for quantifying space by chain or tape.

The most frequent approach used in determining or Setting Away linear measurements for construction surveys, triangulation base and lines traverse Spaces is frequently imputed to asChaining. The name is taken over from the early days when the Gunter’s chain and the engineer’s chain were in use. Now, it is more appropriate to call this operation TAPINGbecause the steel tape has replaced the chains the surveyor’s measuring system.

Clearly, the tiniest chaining party could consist of two individuals–one at each end of the tape. In this manner, the back chairman can keep the head chainman aligned at some of it or all times whenever a total tape span is transferred to the earth. The head chainman additionally act as the recorder, as well as the back chainman is responsible for keeping the tape in alignment. If precision in taping or more speed is needed, added staffs are assigned to the party. This allows them to concentrate mainly on the measurement and takes over the chainmen of some of their responsibilities. For more exact chaining, a three individual team is not dispensable. In addition, to rear chainmen and the head, a stretcher man is added.

Back Tape person

— Maintains alignment by directing forwards tape person towards desirable stage

— Maintains amount by using hand level or alternative device or by eyeballing

Liner In

Indicate both ends and at intermediate stages as needed.

Using Tension

Tape ought to be held and direct at the same level.

Pipes

It needed when surface irregularities or barriers allow it to be undesirable to put the tape on the earth.
Tape used to indicate the tape span and is held in a flat position with a plumb bob over the back point.
The forward tape person paces 100 feet off as well as the procedure is repeated until a partial tape span stays.
Two sorts of tapes
Add cassette is truly 101 feet long
Cut tape needs subtraction to use is 100 feet long
Quantify the space
By counting the amount of personal identification numbers gathered following the partial tape span was quantified, the back tape person ascertains the variety of complete tape spans.

TAPING ON IRREGULAR OR SLOPING EARTH

Hold the cassette horizontal and make use of a plumb at both ends.
Quantify shorter spaces at a time to enable the tape flat at or below chest height.
The back tape person holds the tape mark in the pin while the forward tape person profits and moves.
This is repeated until the total 100 foot space is indicated.
Taping down is easier and preferable to taping.

TAPING A STEEP INCLINE ON

On steep inclines discover the angle of inclination or the difference in elevation and it is generally better to quantify along the incline.

The measurement of space together with the help of tape or chain is known as chaining. The measurement of space together with the help of tape is called taping. Chain surveying needs the assistance of chain, ranging and tapes poles. Metallic tapes are popular in surveying. A metallic tape is made from varnished strip of waterproof line as well as the tape is entwined with little wires of copper and brass.

Measuring systems in Chaining and Taping

Quantifying chain also called surveyor chain is principally used to compute linear spaces. When international satellites to map spaces from space were not in their job with assistance from surveyor chain spaces between points are computed correctly. To make measurements with chains, keep tallying labels in the chain then split it into 10 equal spans as step one in chaining. Make both chainmen. A mark needs to be made at the place of the fore chainman. Everyone is progressed towards the item to be found keeping the chain.

Tape or chain Surveying and its goals

Tape or chain surveying is the easiest type of detail surveying. With the help of cassette system the lengths of lines may be computed and from links in these lines details are gathered. Systems are there to find challenges. Well formed braced quadrilaterals or linked triangles are made with assistance from selected stations. Measuring the space between points with the help of some other similar tools or chain to record the space with the aim of surveying is the fundamental idea in chain surveying. Offsets and link lines are popular in chain kind of surveying.

Observation of flat spaces by taping includes implementing the known time of a calibrated cassette right straight to line several times.

Posted on December 8, 2015 in Civil Engineering Assignment Help

Share the Story

Back to Top
Share This